Leeson Sub-Micro Dynamic Braking Kit for Int Resistor Instrukcja Użytkownika Pobierz pdf

SUB-MICRO SERIES DYNAMIC BRAKING OPTION (FOR MODELS RATED 0.25 - 10 HP)

INSTALLATION AND OPERATION INSTRUCTIONS

Manual Number: SDBR06C

The Sub-Micro Series Dynamic Braking option can be used with all SM, SM-Plus and SM-Basic models.

WARNING!

Remove power from the drive and wait three minutes before wiring the DB module. Incorrect wiring of the B+ and B- terminals will result in

equipment damage! The B+ terminal on the DB module must be connected to the B+ terminal on the Sub Micro drive, and the B- terminal on the DB

module must be connected to the B- terminal on the Sub-Micro drive.

DO NOT make connections to R+ and R- without consulting LEESON. Damage to the Dynamic Braking module and/or drive may result.

SM-PLUS SERIES DRIVES

PROGRAMMING

1. Set Parameter 09 (TB-31 OUTPUT) to DYNAMIC BRAKING (04).

2. Set Parameter 10 (TB-13A FUNCTION) to DB FAULT (09), or set Parameter 12

(TB-13C FUNCTION) to DB FAULT (08).

WIRING

The diagram to the right illustrates how the DB module is wired to the SM-PLUS Series

drive. In this diagram, TB-13A is used as the DB FAULT input, but TB-13C could be

used instead if TB-13A is required for another function.

NOTE 1: Use 18 AWG wire for control connections.

NOTE 2: Use minimum 14 AWG wire for connections to B+ and B-. The B+ and B-

wires MUST be twisted together and must be less than 12 inches long.

NOTE 3: DO NOT make connections to R+ and R- without consulting LEESON.

Damage to the Dynamic Braking module and/or drive may result.

SM-PLUS

POWER

TERMINALS

SM-PLUS

CONTROL

TERMINALS

DB OPTION MODULE

13A231

GND

B - B + R + R -

B - B +

SM-PLUS DIAGRAM

(SEE NOTE 3)

SM SERIES DRIVES

PROGRAMMING

1. Set Parameter 12 (TB-13E FUNCTION) to DYNAMIC BRAKING (20).

2. Set Parameter 10 (TB-13A FUNCTION) to INVERSE EXT. FAULT (09), or set

Parameter 11 (TB-13B FUNCTION) to INVERSE EXT. FAULT (10).

WIRING

The diagram to the right illustrates how the DB module is wired to the SM Series drive.

In this diagram, TB-13A is programmed for INVERSE EXTERNAL FAULT, but TB-

13B could be used instead if TB-13A is required for another function.

NOTE 1: Use 18 AWG wire for control connections.

NOTE 2: Use minimum 14 AWG wire for connections to B+ and B-. The B+ and B-

wires MUST be twisted together and must be less than 12 inches long.

NOTE 3: DO NOT make connections to R+ and R- without consulting LEESON.

Damage to the Dynamic Braking module and/or drive may result.

POWER

TERMINALS

CONTROL

TERMINALS

DB OPTION MODULE

13A13E 11

GND

B - B + R + R -

B - B +

SM DIAGRAM

(SEE NOTE 3)

LEESON ElectricLEESON Electric

LEESON Electric • 2100 Washington St. • Grafton, WI 53024 • Ph: (262) 377-8810 • Fax: (262) 377-9025 • www.leeson.com

1 2

Podsumowanie treści

Strona 1 - SM SERIES DRIVES

SUB-MICRO SERIES DYNAMIC BRAKING OPTION (FOR MODELS RATED 0.25 - 10 HP)INSTALLATION AND OPERATION INSTRUCTIONSManual Number: SDBR06CThe Sub-Micro Seri

Strona 2 - SM-BASIC SERIES DRIVES

MOUNTING THE DYNAMIC BRAKING MODULEThe diagram below illustrates how to mount the DB Module. The DBModule is compatible with the DIN Rail Mounting Ki

Komentarze do niniejszej Instrukcji

Brak uwag

Leeson Sub-Micro Dynamic Braking Kit for Int Resistor Instrukcja Użytkownika

Przeglądaj online lub pobierz Instrukcja Użytkownika dla Oprogramowanie Leeson Sub-Micro Dynamic Braking Kit for Int Resistor. LEESON Sub-Micro Dynamic Braking Kit for Int Resistor User Manual Instrukcja obsługi

Podsumowanie treści

Komentarze do niniejszej Instrukcji

Powiązane produkty i podręczniki dla Oprogramowanie Leeson Sub-Micro Dynamic Braking Kit for Int Resistor